HPI Plazma 7.4v 4000mah 20c Lipo Round Case Stick Pack 29.6wh 101941

HPI Plazma 7.4v 4000mah 20c Lipo Round Case Stick Pack 29.6wh 101941
Brand: HPI
Part Number: 101941
RRP: £29.99. Save £3.00
Availability:    On Order with Supplier Email Me  
EAN: 4944258520476
Save:   Add to wishlist

Request Stock Notification

Your Email:
Reviews: 5 Stars5 Stars5 Stars5 Stars5 Stars
Our Price: £26.99

Important Product Safety Information   

Lithium batteries can be dangerous if not handled correctly.
These safety points are to be used as a general guide.
Please refere to the specific user instruction and warnings supplied with your Lithium battery before use.

ONLY use a charger designed for lithium batteries.
ALWAYS use a safe sack, charging pouch or fireproof container to place your batteries in whilst charging.
ALWAYS use the balance lead connection when charging.
NEVER use a NiMh or NiCad charger.
NEVER charge the batteries unattended.
NEVER leave the battery connected when not in use.

General Guidelines and Warnings:

  • Use specific Lithium Polymer/Li-ion charger only. Do not use a NiMH or NiCd charger. Failure to do so may a cause fire.
  • Never charge batteries unattended. When charging LiPo/Li-ion batteries you should always remain in constant observation to monitor the charging process and react to potential problems that may occur.
  • Some LiPo/Li-ion chargers on the market may have technical deficiencies that may cause it to charge the LiPo/Li-ion batteries incorrectly or at an improper rate. It is your responsibility solely to assure the charger you purchased works properly. Always monitor charging process to assure batteries are being charged properly. Failure to do so may result in fire.
  • If at any time you witness a battery starting to balloon, swell up, smoke or get hot, discontinue charging process immediately, disconnect the battery and observe it in a safe place for approximately 15 minutes. This may cause the battery to leak, and the reaction with air may cause the chemicals to ignite, resulting in fire.
  • Since delayed chemical reaction can occur, it is best to observe the battery as a safety precaution. Observation should occur in a safe area outside of any building or vehicle and away from any combustible material.
  • Wire lead shorts can cause fire! If you accidentally short the wires, the battery must be placed in a safe area for observation for approximately 15 minutes. Additionally, if a short occurs and contact is made with metal (such as rings on your hand), severe injuries may occur due to the conductibility of electric current.
  • A battery can still ignite even after 10 minutes.
  • In the event of damage due to bad shipment or other reason, you must remove battery for observation and place in a safe open area away from any combustible material for approximately 15 minutes.
  • If for any reason you need to cut the terminal wires, it will be necessary to cut each wire separately, ensuring the wires to not touch each other or a short may occur, potentially causing a fire.
  • To solder a connector: Remove insulating tape of Red wire and solder to positive terminal of a connector, then remove insulating tape of Black wire and solder to the negative terminal of connector. Be careful not to short the wire lead. If you accidentally cause the battery to short, place it in a safe open space and observe the battery for approximately 15 minutes. A battery may swell or even possibly catch fire after a short time.
  • Never store or charge battery pack inside your car in extreme temperatures, since extreme temperature could ignite fire.

Popular Options

 Good Stock    £6.49

Brand new from HPI is the Plazma 4000mAh 7.4v LiPo pack. Features like a stickpack shaped hard case, factory fitted Deans connector 20C discharge rate and a JST-XH balance lead will surely make these a hit!

Spec check:

  • 7.4v 4000mAh LiPo
  • 20C nominal discharge
  • Stick pack shaped hard plastic case
  • Factory fitted Deans power plug
  • JST-XH balance connector
5 Stars5 Stars5 Stars5 Stars5 Stars (1 Rating)

Have this running on Tamiya Mud Blaster along with HPI Flux shot brushless motor and flux reload v2 esc. It lasts a decent amount of time, hard case is great and fits perfectly in the chassis as a replacement for nimh 7.2. Using this with above ESC gives lipo protection and comes with Deans connector. Highly recommend this setup for more than enough useable power on Tamiya 1:10 cars!!

5 Stars5 Stars5 Stars5 Stars5 Stars  Posted on 22nd Sep